Reloading Advice from Sinclair Int’l

cartridge reloadingSinclair International’s Reloading Press Blog recently featured a “round-table” discussion of reloading techniques. Sinclair’s team of tech staffers were asked: “What do you feel is the one-most crucial step in precision reloading?”

Here are their responses (along with comments from our Editors):

Phil Hoham: “I feel that when working up a load do not go too high or too low in your powder charge. Stay away from “suggested loads” you hear at the range, or on the internet. Always be sure to use a published reloading manual that presents not only minimums and maximums, but also pressure, velocity, and a proper range of powders used. Do not get distracted in the reloading process, and remain focused at all times during each step involved.”

AccurateShooter.com: Some loads presented on the Internet are OK as a starting point, but it is absolutely critical to understand that pressure maximums will vary considerably from one rifle to another (of the same chambering). For example, one 6mmBR rifle shooting 105gr bullets can max out with 30.0 grains of Varget powder, while another rifle, with the same chamber dimensions, but a different barrel, could tolerate (and perform better) with half a grain more powder. You need to adjust recommended loads to your particular rifle and barrel.

Froggy Reloading Bench

Pete Petros: “This could be a very broad topic, but if I were to pick one, it would be making sure to pay close attention, and weigh each and every powder charge to ensure that each load is exact and consistent. This is important not only for accuracy, but also for safety reasons.”

AccurateShooter.com: If you’re shooting beyond 200 yards, it is critical to weigh your loads with an accurate scale. Loads that are uniform (within a few kernels) will exhibit lower Extreme Spread and Standard Deviation. And remember, even if you stick with the same powder, when you get a new powder lot, you may have to adjust your load quite a bit. For example, .308 Palma shooters have learned they may need to adjust Varget loads by up to a full grain from one lot of Varget to the next.

Ron Dague: “I feel that the most important step(s) in reloading for accuracy are in the initial case prep. Uniforming the primer pocket to the same depth to ensure consistency in primer seating is a crucial step. Additionally de-burring the flash holes, each in the same way to clean up and chamfer the inside is important. It ensures that the ignition from the primer is uniform and flows out in the same consistent pattern. Doing so will create uniform powder ignition and tighten up your velocity Extreme Spread.”

AccurateShooter.com: With some brands of brass, primer pocket uniforming and flash-hole deburring is useful. However, with the best Lapua, Norma, and RWS brass it may be unnecessary, or worse, counter-productive. So long as your Lapua brass flash-holes are not obstructed or smaller than spec, it may be best to leave them alone. This is particularly true with the small flash holes in 220 Russian, 6BR, and 6.5×47 cases. MOST of the flash-hole reaming tools on the market have cutting bits that vary in size because of manufacturing tolerances. We’ve found tools with an advertised diameter of .0625″ (1/16″) that actually cut an 0.068″ hole. In addition, we are wary of flash-hole deburring tools that cut an aggressive inside chamfer on the flash-holes. The reason is that it is very difficult to control the amount of chamfer precisely, even with tools that have a depth stop.

Rod Green: “I feel that bullet seating is the most important step. If you had focused on making sure all prior steps (case prep, powder charge, etc.) of the process have been carefully taken to ensure uniformity, bullet seating is the last step, and can mean all the difference in the world in terms of consistency. Making sure that the bullet is seated to the same depth each time, and time is taken to ensure that true aligned seating can make the load.”

Bob Blaine: “I agree with Rod. I strongly feel that consistent bullet seating depth is the most important step in creating the most accurate hand loads. I have seen the results in both my bench and long range rifles. Taking the time to ensure exactness in the seating process is by far, the number one most important step in my book.”

AccurateShooter.com: Agreed. When loading match ammo, after bullet seating, we check every loaded round for base of case to ogive length. If it varies by more than 3 thousandths, that round is segregated or we attempt to re-seat the bullet. We measure base of case to bullet ogive with a comparator mounted on one jaw of our calipers. You may have to pre-sort your bullets to hold the case-base to ogive measurement (of loaded rounds) within .003″.

Tags: , , ,

700-505 640-911 M70-301 70-489 700-501 M70-101 70-458 70-341 70-464 70-680 74-335 70-687 70-457 n10-005 1z0-061 220-801 70-465 exam C4090-958 MB2-867J MB2-868 MB2-876 MB3-207 MB3-208 MB3-209 MB3-210 MB3-214 MB3-215 MB3-216 MB3-230 P2060-001 P2060-002 P2060-017 P2070-055 P2070-071 P2070-072 VCAW510 VCP-310 VCP-410 VCP-411 VCP-510 VCP-511 VCP-550 1Z1-821 1Z1-822 1Z1-850 1Z1-851 74-353 74-404 74-409 74-674 74-676 70-410 70-460 70-461 70-462 200-120 70-488 MB2-703 70-411 mb5-705 70-346 70-486 70-347 70-480 70-483 70-412 70-463 mb2-700 3X0-203 3X0-204 400-051 400-101 500-005 500-051 500-201 500-254 500-285 510-014 510-015 810-420 820-421 820-422 83-640 850-001 920-093 A2040-986 A2040-988 A2050-219 A2050-723 BR0-002 BR0-003 C_A1FIN_10 C_BOCR_08 CX-310-019 CX-310-027 CX-310-052 CX-310-053 MB2-498 MB2-631 MB2-632 MB2-633 MB2-634 MB2-700 MB2-701 MB2-702 MB2-703 MB2-866 MB2-867 642-054 642-055 642-061 642-062 642-066 642-067 642-071 642-072 642-081 642-091 070-086 070-089 070-121 070-122 070-123 070-158 070-162 070-169 070-177 070-178 070-181 070-210 070-214 E20-016 E20-017 E20-018 E20-040 E20-050 E20-060 HP0-207 HP0-216 HP0-236 HP0-238 HP0-239 HP0-240 HP0-242 JN0-694 JN0-696 JN0-730 L50-501 L50-502 L50-503 LOT-402 LOT-403 LOT-404 windows 7 key windows 7 key windows 7 key windows 7 key Windows-8-Enterprise-Key Windows-8-Enterprise-Key-sale cheap-Windows-8-Key Windows-8-1-Key Windows-8-Standard-Key Windows-8-Standard-Key-online buy-Windows-8-Standard-Key windows-7-key buy-windows-7-key windows-7-key-sale cheap-windows-7-key-for-sale windows-7-key-sale-oem windows-7-key-sale-finmde buy-Windows-8-Key windows-7-key-for-sale cheap-windows-7-key-sale windows-7-ultimate-serial-product 18630-product-key-number windows-7-all-number windows-7-product-keys windows-8-professional-product-keys windows-8-product-keys-serial-keys windows-8-professional-product-key windows-8-product-key Office-2013-Professional-Key Office-2010-Professional-Key windows81-product-key